halftrackinfo

classified ads => halftracks and parts wanted => Topic started by: Prc148 on January 06, 2019, 09:32:44 AM

Title: Parts wanted for Diamond-T M3
Post by: Prc148 on January 06, 2019, 09:32:44 AM
WTB for Diamond T M3:

1. 18G winch parts
2. Co-driver seat stop pivot arm.
3. Early Headlight buckets
4. PTO seals/packing
5. Rear door latch
6. Winch bumper pieces
7. Track/rear armor




Title: Re: Parts wanted for Diamond-T M3
Post by: steve1973 on January 06, 2019, 05:35:25 PM
PM sent.

Steve A
Title: Re: Parts wanted for Diamond-T M3
Post by: Prc148 on March 09, 2019, 06:26:32 AM
Updated
Title: Re: Parts wanted for Diamond-T M3
Post by: Prc148 on September 11, 2019, 07:18:36 PM
WTB for Diamond T M3:

5. Co-driver seat w/seat stop and hinges

9. Early Headlight buckets
Updated
Title: Re: Parts wanted for Diamond-T M3
Post by: Prc148 on September 27, 2019, 05:34:17 AM
Updated
Title: Re: Parts wanted for Diamond-T M3
Post by: steve1973 on September 27, 2019, 04:39:46 PM
Check out eBay for the headlights. here is a link below

https://www.ebay.com/itm/Early-WW2-Guide-Cycle-Ray-headlights-Half-Track-Scout-Harley-Servi-Car-1940-45/113901434810?hash=item1a850df7ba:g:XN0AAOSwJMZdjNRL

Steve A.
Title: Re: Parts wanted for Diamond-T M3
Post by: Prc148 on October 10, 2019, 06:59:57 AM
I was out bid...again.
Title: Re: Parts wanted for Diamond-T M3
Post by: Prc148 on October 10, 2019, 07:03:53 AM
I’ll be traveling through W. PA, OH MI early Nov so I can pick up if anyone wants to sell. May be heading back through IN, KY and TN.
Title: Re: Parts wanted for Diamond-T M3
Post by: Prc148 on November 27, 2019, 12:58:51 PM
WTB for Diamond T M3:

1. 18G winch parts
2. Co-driver seat stop pivot arm.
3. Early Headlight buckets
4. Rear door latch mechanism
5. PTO shaft
6. Winch bumper pieces
7. Track/rear armor and floor/seat pieces.
8. Top rail angle iron above doors and top of rear armor- (not A1).
9. 50% or better used tracks
Title: Re: Parts wanted for Diamond-T M3
Post by: Darth_Kitten on November 27, 2019, 02:29:24 PM
I've not looked into it yet, but wouldn't the seat stop pivot arm be an off the shelf item. Maybe McMaster Carr? I don't have one to use as an example, but perhaps someone could take a measurement? (I need one too).
If you are OK with it, get a set of reproduction WLA Harley headlights and modify to fit. I think that's what Steve was doing earlier (I bought mine from him).
Paul Jacobs might be a resource for the rear latch. Shoot him a PM.
I'm going to try to source the perimeter rail locally. I have scrap piece to use as an example to see if a local shop can fab some up.
I hope this helps.
WTB for Diamond T M3:

1. 18G winch parts
2. Co-driver seat stop pivot arm.
3. Early Headlight buckets
4. Rear door latch mechanism
5. PTO shaft
6. Winch bumper pieces
7. Track/rear armor and floor/seat pieces.
8. Top rail angle iron above doors and top of rear armor- (not A1).
9. 50% or better used tracks
[/quote]
[/quote]
Title: Re: Parts wanted for Diamond-T M3
Post by: col.halftrack on November 27, 2019, 03:30:10 PM
 I have a few early headlamp buckets. I also have NOS and repro winch driveshafts. I have new production track sets.
kplockwood@cox.net
Title: Re: Parts wanted for Diamond-T M3
Post by: Prc148 on February 08, 2020, 07:25:44 AM
List updated. I’m going to make the perimeter rail based on a piece I found. Rebuilding PTO now and looking for the packing seals.