Author Topic: Parts wanted for Diamond-T M3  (Read 1581 times)

Prc148

  • Newbie
  • *
  • Posts: 29
Parts wanted for Diamond-T M3
« on: January 06, 2019, 09:32:44 AM »
WTB for Diamond T M3:

1. 18G winch parts
2. Co-driver seat stop pivot arm.
3. Early Headlight buckets
4. PTO handle
5. PTO shaft
6. Winch bumper pieces
7. Track/rear armor




« Last Edit: October 10, 2019, 07:04:34 AM by Prc148 »

steve1973

  • Hero Member
  • *****
  • Posts: 1212
Re: Parts wanted for Diamond-T M3
« Reply #1 on: January 06, 2019, 05:35:25 PM »
PM sent.

Steve A

Prc148

  • Newbie
  • *
  • Posts: 29
Re: Parts wanted for Diamond-T M3
« Reply #2 on: March 09, 2019, 06:26:32 AM »
Updated

Prc148

  • Newbie
  • *
  • Posts: 29
Re: Parts wanted for Diamond-T M3
« Reply #3 on: September 11, 2019, 07:18:36 PM »
WTB for Diamond T M3:

5. Co-driver seat w/seat stop and hinges

9. Early Headlight buckets
Updated

Prc148

  • Newbie
  • *
  • Posts: 29
Re: Parts wanted for Diamond-T M3
« Reply #4 on: September 27, 2019, 05:34:17 AM »
Updated

steve1973

  • Hero Member
  • *****
  • Posts: 1212

Prc148

  • Newbie
  • *
  • Posts: 29
Re: Parts wanted for Diamond-T M3
« Reply #6 on: October 10, 2019, 06:59:57 AM »
I was out bid...again.

Prc148

  • Newbie
  • *
  • Posts: 29
Re: Parts wanted for Diamond-T M3
« Reply #7 on: October 10, 2019, 07:03:53 AM »
I’ll be traveling through W. PA, OH MI early Nov so I can pick up if anyone wants to sell. May be heading back through IN, KY and TN.

Prc148

  • Newbie
  • *
  • Posts: 29
Re: Parts wanted for Diamond-T M3
« Reply #8 on: November 27, 2019, 12:58:51 PM »
WTB for Diamond T M3:

1. 18G winch parts
2. Co-driver seat stop pivot arm.
3. Early Headlight buckets
4. Rear door latch mechanism
5. PTO shaft
6. Winch bumper pieces
7. Track/rear armor and floor/seat pieces.
8. Top rail angle iron above doors and top of rear armor- (not A1).
9. 50% or better used tracks

Darth_Kitten

  • Sr. Member
  • ****
  • Posts: 266
Re: Parts wanted for Diamond-T M3
« Reply #9 on: November 27, 2019, 02:29:24 PM »
I've not looked into it yet, but wouldn't the seat stop pivot arm be an off the shelf item. Maybe McMaster Carr? I don't have one to use as an example, but perhaps someone could take a measurement? (I need one too).
If you are OK with it, get a set of reproduction WLA Harley headlights and modify to fit. I think that's what Steve was doing earlier (I bought mine from him).
Paul Jacobs might be a resource for the rear latch. Shoot him a PM.
I'm going to try to source the perimeter rail locally. I have scrap piece to use as an example to see if a local shop can fab some up.
I hope this helps.
WTB for Diamond T M3:

1. 18G winch parts
2. Co-driver seat stop pivot arm.
3. Early Headlight buckets
4. Rear door latch mechanism
5. PTO shaft
6. Winch bumper pieces
7. Track/rear armor and floor/seat pieces.
8. Top rail angle iron above doors and top of rear armor- (not A1).
9. 50% or better used tracks
[/quote]
[/quote]

col.halftrack

  • Sr. Member
  • ****
  • Posts: 348
Re: Parts wanted for Diamond-T M3
« Reply #10 on: November 27, 2019, 03:30:10 PM »
 I have a few early headlamp buckets. I also have NOS and repro winch driveshafts. I have new production track sets.
kplockwood@cox.net
1941 White M2
1942 White M4A1 was M4
1942 Autocar M2A1
1942 Autocar M3-75
1943 White M13 rebuilt as M16
1943 Diamond T M3A1